PoE Powered Industrial Switch 8 Port 8RJ45 4SFP 12V24V 802.3u 100Base-TX Din-rail

Gigabit managed Industrial ethernet Switch 

Introduction of Industrial Fiber Media Converter

Product Features of managed hardened switch

•  8 x 10/100/1000Mbps Auto-sensing RJ45 ports
•     4 x 10/100/1000Mbps SFP fiber port
• 4 KV Ethernet surge protection, adapt to a harsh outdoor environment
• Support Auto MDI/MDIX
• Flow control mode: full duplex with IEEE 802.3x standard, half-duplex with Back pressure standard
• IEEE 802.3 10Base-T and IEEE 802.3u 100Base-TX compliant
• A store-and-forward switching mechanism
• Operating environment temperature:-40 ° ~85 ° c
• Support cable diagnosis and can locate the fault point
• Support IEEE802.3az EEE (Energy Efficient Ethernet) Management, optimize power consumption
• Support STP, RSTP, MSTP, ITU-T G.8032 Ethernet Protection Ring(EPR)
• Support Qos, transport classification Qos, Cos, bandwidth control (input/output direction), storm suppression       ,differentiated services
• Support IEEE802.1q VLAN,VLAN port ,based Mac VLAN,IP subnet VLAN, Protocol VLAN,VLAN convert,       MVR
• Support dynamic IEEE802.3ad LACP link aggregation, static link aggregation
• Support IGMP/MLD snooping V1/V2/V3, IGMP filtrating/ modulating, IGMP searching
• Support IGMP agent report, MLD snooping
• Safety: based on port and Mac IEEE802.1X, RADIUS, ACL, TACACS+,HTTP/HTTPS, SSL/SSH v2
• Support Cisco® like CLI, Web management, SNMP v1/v2c/v3, Telnet
• Support software upgrade via TFTP and HTTP, firmware redundancy prevents upgrade failing
• Support DHCP client/Relay/Snooping/Snooping option 82/Relay option 82
• Support RMON, MIB II, mirror image, event log, DNS, NTP/SNTP, IEEE802.1ab LLDP
• Support IPV6 Telnet server /ICMP v6, SNMP, HTTP, SSH/SSL, NTP/SNTP,TFTP, QoS, ACL

About Olycom

• Olycom manufactures and markets fiber optic connectivity devices.
• Olycom provides solutions and services of industrial fiber switch, fiber to copper media conversion, Ethernet networking, and CCTV video surveillance.
• Olycom currently focuses on

Industrial Networking
Optical Bypass
WDM Equipment
Optical Monitoring Systems
POE++

Packing box of Din rail managed switch

Production steps

• Welding: Weld the necessary components
• Cleaning: To avoid any possible dysfunction due to dust or scraps on the PCB boards.
• Assembling: Builds up components of a product, like panels, screws, PCB boards.
• Testing: To make sure the product is basically working fine after assembling
• Aging: To check if the product can work smoothly for long time without any minors such as LED indicators, voltage. This will usually last for 24 to 48 hours.
• Testing: To test if the product can process data or video signals correctly. Any data loss? Transmission rate correct? Any data packet failure? Such questions would be verified in this procedure.
• QC testing: This is the third and also last check of product quality. If it goes good, our packing staff will pack it up according to customer requirements and attach to the packing box a product label.
• When all above is done, the product will go to market.

PoE industrial switch 8 port

802.3u industrial switch 8 port

9V poe powered poe switch

PoE Powered Industrial Switch 8 Port 8RJ45 4SFP 12V24V 802.3u 100Base-TX Din-rail Images